Private customers can also find our range in our partner store Ampha-Analyse.
Reagent for CALDUR® pH / chlorine (free) – Colorimetric:
See also:
CALDUR® pH / Chlorine (free) test set – Colorimetric
What are pH and free chlorine measured for?
pH value and free chlorine are the two most important parameters for monitoring swimming and bathing pool water. The pH value directly influences the disinfection effect of chlorine: The effectiveness of chlorine is highest at an optimum pH value (7.0-7.4).
This practical combination test set enables the simultaneous determination of both parameters and is therefore the ideal tool for daily swimming pool monitoring.
Standard values for swimming pool water: pH 7.0-7.4, free chlorine 0.3-0.6 mg/l (DIN 19643).
How does the test set work?
The combination test set contains two separate measuring systems: pH measurement: After adding phenol red Reagent, the sample changes color from yellow (acidic) to orange to red (basic) depending on the pH value. Chlorine measurement: After adding the DPD reagents (chlorine A + B), the sample turns pink to violet in proportion to the chlorine concentration.
Advantages of the CALDUR® test set
Two parameters in one test set
Measure pH and free chlorine simultaneously – time-saving and practical
Quick analysis in just 1 minute
Ideal for daily swimming pool checks
50 determinations per parameter
Economical for regular checks
pH range 6.8 – 8.0
Optimized for the swimming pool area
Chlorine range 0.1 – 1.0 mg/l
Covers the recommended range for swimming pool water
Areas of application
Pond / lake
Groundwater / well water
Drinking / tap water
Aquaristics
Pool / Swimming pool
Industrial processing
Boiler water
Food preparation
Waste water treatment
Carrying out the measurement:
pH measurement:
Fill water sample into pH test tubes up to the 10 ml mark
Add 5 drops of phenol red Reagent and mix
Compare color with pH color chart
Chlorine measurement:
Fill the water sample into chlorine test tubes up to the 10 ml mark
Add 5 drops of chlorine A and mix
Add 3 drops of chlorine B and mix
Immediately compare color with chlorine color chart (within 1 minute)
Tip for best results
The measurement should be taken directly at the edge of the pool, as chlorine is more volatile than is often assumed. Measure at different points in the pool to obtain a representative picture. Ideal measurement times: in the morning before bathing and in the evening after closing.
Important notes
Measure the sample immediately after taking it – chlorine volatilizes
Read chlorine measurement within 1 minute
Avoid direct sunlight during the measurement
If the chlorine color fades: dilute the sample and measure again
Thoroughly rinse the test tube with the sample before each measurement
Always check pH and chlorine together – they influence each other
Measuring range pH
Measuring level
Description
6,8
Slightly acidic (yellow-orange)
7,2
Optimal – lower range (orange)
7,6
Optimal – upper range (red-orange)
8,0
Slightly alkaline (red)
Measuring range chlorine (free)
Measuring level
Description
0.1 mg/l
Low concentration (pale pink)
0.5 mg/l
Average concentration (pink)
1.0 mg/l
High concentration (strong pink)
Read intermediate values:
If the color lies between two fields, you can calculate the average value.
Number of possible destinations
With a CALDUR® test set pH / chlorine (free) you can carry out 50 measurements per parameter.
This refers to the quantity of reagents contained.
Measuring accuracy and reproducibility
Readability pH: ± 0.2 pH units Chlorine readability: ± 1 color level Reproducibility: Very good if the application instructions are followed Interference Chlorine: Bromine and other oxidizing agents also react with DPD. At high concentrations, color fading may occur – in this case, dilute the sample.
What to do if measured values are out of range?
Chlorine > 1.0 mg/l
Verduction
Execution
Calculation of the measured value
1:1
5 ml sample + 5 ml chlorine-free water
Measured value × 2
pH outside 6.8-8.0
Use the appropriate CALDUR® pH test set (pH 2-5, pH 5-8 or pH 8-12) for the corresponding range.
Specifications at a glance
Reagents (3 reagents)
Property
Value
Parameters
pH value + free chlorine (Cl₂)
Item number
31-072290
Method
Colorimetric (phenol red / DPD)
Measuring principle
Color comparison with color charts
Measuring range pH
6,8 / 7,2 / 7,6 / 8,0
Measuring range chlorine
0.1 / 0.5 / 1.0 mg/l Cl₂
Analysis duration
1 minute
Number of determinations
50 each (pH and chlorine)
Reagents pH
1 (phenol red)
Reagents Chlorine
2 (Chlorine A + B, DPD)
Packaging
Hinged lid box
Packaging size
103 x 91 x 36 mm
weight
approx. 170 g
Scope of delivery
3 reagent bottles (phenol red, chlorine A, chlorine B) with detailed labeling
2 test tubes (1x pH, 1x chlorine) with 10 ml scale
2 color cards (1x pH with 4 measuring levels, 1x chlorine with 3 measuring levels)
Detailed operating instructions (DE/EN)
Safety data sheets for all reagents
Robust hinged lid box (103 x 91 x 36 mm)
Reagent details
Reagent
Volume
Shelf life
Notes
Phenol red (pH Reagent)
15 ml
24 months (24M)
pH Reagent, shake before use
Chlorine A (DPD 1)
15 ml
24 months (24M)
DPD reagent, shake before use
Chlorine B (buffer)
10 ml
24 months (24M)
Buffer solution, shake before use
Shelf life: The shelf life starts from the date of manufacture (printed on the bottle).
After opening, the reagents should be used within 12 months.
Store the test kit in a dry, cool place (10-25°C) and protected from direct sunlight.
Reagent for CALDUR® pH / chlorine (free) – Colorimetric:
We use cookies
We use cookies and analytics services (e.g. Google Analytics) to improve our website. Technically necessary services are always on. You can accept or decline optional services. More in the privacy policy