Caldur® pH 8-12 – Colorimetric
pH determination in the alkaline range using a color chart (pH 8-12)
Private customers can also find our range in our partner store Ampha-Analyse.
Reagent for Caldur® pH 8-12 – Colorimetric:
See also:
CALDUR® pH 8-12 test set – Colorimetric
What is the pH value 8-12 measured for?
The pH range 8-12 covers the alkaline to strongly alkaline range that must be monitored in numerous industrial applications. Boiler water, cooling water with inhibitors and alkaline cleaning solutions are typically in this pH range.
In boiler technology, the feed water is often set to pH 9-10 to minimize corrosion. Monitoring is essential, as both too low and too high pH values can cause damage to the system.
In wastewater treatment, alkaline wastewater must be neutralized before discharge. The pH limit value for discharges is pH 6.5-9.5.
How does the test set work?
The CALDUR® pH 8-12 Test Set – Colorimetric uses a mixing indicator that takes on a characteristic color depending on the pH value of the sample. After adding a reagent to the water sample, the color is compared with the supplied color chart within 1 minute.
Advantages of the CALDUR® test set
- Optimized for the alkaline pH range 8-12
Higher resolution in the alkaline range than universal pH test sets
- 300 provisions per set
Very economical for continuous use
- Fastest analysis in just 1 minute
Immediate results on site
- Only 1 reagent required
Particularly quick and easy handling
- Robust plastic housing with hinged lid
Safe transportation and protection of reagents
Areas of application
Carrying out the measurement:
- Fill water sample into test tubes up to the 10 ml mark
- Add 5 drops of mixing indicator and mix
- Wait 1 minute
- Perform color comparison with color chart
Tip for best results
The sample should have a temperature between 15 and 25°C, as the pH value is temperature-dependent. If the boiler water is hot, allow the sample to cool down to room temperature before measuring. CO₂ losses during cooling can increase the pH value.
Important notes
- Take care when handling strongly alkaline samples – wear protective gloves
- Heavily colored samples can make reading difficult
- Strong reducing agents can influence the Reagent
- Thoroughly rinse the test tube with the sample before each measurement
- Perform color comparison in daylight
Measuring range
| Measuring level | Description |
|---|---|
| pH 8.0 | Slightly alkaline (blue-green) |
| pH 8.5 | Alkaline (blue) |
| pH 9.0 | Moderately alkaline (strong blue) |
| pH 10.0 | Strongly alkaline (blue-violet) |
| pH 11.0 | Very strongly alkaline (violet) |
| pH 12.0 | Extremely alkaline (dark violet) |
If the color lies between two fields, you can form the mean value
(e.g. between pH 9.0 and 10.0 = approx. pH 9.5).
Number of possible destinations
With a CALDUR® pH 8-12 test set you can carry out 300 measurements.
This refers to the quantity of reagents contained.
Measuring accuracy and reproducibility
Readability: ± 0.5 pH units
Reproducibility: Very good if the application instructions are followed
Interference: Heavily colored or true samples can make color readings difficult. The Reagent may deviate slightly at very high salt concentrations. Strong reducing agents can influence the Reagent.
What to do if measured values are out of range?
Measured value > pH 12
The sample is extremely alkaline. Dilute the sample 1:10 with distilled water and measure again. The actual pH value is then correspondingly higher than the value read.
Measured value < pH 8
Use the CALDUR® pH 5-8 test set for the neutral range.
Specifications at a glance
Reagents (1 reagent)
| Property | Value |
|---|---|
| Parameters | pH value (basic) |
| Item number | 31-072390 |
| Method | Colorimetric (mixing indicator) |
| Measuring principle | Color comparison with 6-stage color chart |
| Measuring range | pH 8 to 12 |
| Color scale | 6 measuring levels (8.0 / 8.5 / 9.0 / 10.0 / 11.0 / 12.0) |
| Analysis duration | 1 minute |
| Number of provisions | 300 |
| Number of reagents | 1 |
| Packaging | Hinged lid box |
| Packaging size | 103 x 91 x 36 mm |
| weight | approx. 120 g |
| Scope of delivery |
|---|
| 1 reagent bottle (mixing indicator) with detailed labeling |
| 1 test tube with 10 ml scale |
| 1 color card with 6 measuring levels |
| Detailed operating instructions (DE/EN) |
| Safety data sheets for all reagents |
| Robust hinged lid box (103 x 91 x 36 mm) |
Reagent details
| Reagent | Volume | Shelf life | Notes |
|---|---|---|---|
| Mixing indicator (pH 8-12) | 30 ml | 24 months (24M) | Indicator solution, shake before use |
Shelf life: The shelf life starts from the date of manufacture (printed on the bottle).
After opening, the reagents should be used within 12 months.
Store the test kit in a dry, cool place (10-25°C) and protected from direct sunlight.
Additional information
| Packaging | Hinged lid box, Refill pack |
|---|
Flyer
Operating instructions
Similar articles:
Related products
-
Total hardness determination in water by titration (0.1 / 0.05 °dH per drop) -
-
